Results 1 to 10 of 10

Thread: Tube amp noise at start up

  1. #1
    Forum Member
    Join Date
    Mar 2024
    Posts
    1

    Tube amp noise at start up

    I bought a Fender Tweed Blues Junior IV Ltd Edition brand new a few years ago. Never left the house and rarely played.

    Recently fired it up and there was a lot of crackle, then verged on feedback, then went quiet and played normally.

    I'm cycling it a few times, letting it cool, the restarting. Can I expect the crackling to diminish with more frequent use?

    It is very quiet (as to extraneous noise) and sounds great as soon as the start up trauma passes.

    Per suggestions, I have carefully pulled out & reinstalled each tube & I have run all the knobs back & forth multiple times.
    More detail. After about 3 - 4 seconds of crackle, a feedback loop starts and crescendos in another 5-10 seconds, then quiet and the amp works normally with no background noise. Any idea on the feedback? I've made sure I had the amp freestanding and not backed up against a wall or corner.

    All the above happens with ALL the knobs at usual settings (mid range) OR zero'd out at turn on.
    Last edited by kydave19; 03-06-2024 at 11:55 AM.

  2. #2
    Forum Member
    Join Date
    May 2023
    Posts
    13

    Re: Tube amp noise at start up

    Sounds like your tube sockets need retentioning (using a thin sharp probe to close off the tube socket pin receptors). The fact you hear crackling until it warms up indicates the pin tube receptors are spread open to far and with heat making better contact when the amp heats up.

  3. #3
    Forum Member phantomman's Avatar
    Join Date
    Aug 2007
    Location
    Ten miles from the Mexican Frontier, in Arizona
    Posts
    7,332

    Re: Tube amp noise at start up

    My money's on a marginal solder joint on the PCB or a ribbon connector that's partially unseated.
    "When injustice becomes law then rebellion becomes duty."

  4. #4
    Forum Member
    Join Date
    May 2023
    Posts
    13

    Re: Tube amp noise at start up

    Quote Originally Posted by phantomman View Post
    My money's on a marginal solder joint on the PCB or a ribbon connector that's partially unseated.
    Yes, that is also a possibility and what I would say to check first.
    I am used to point to point wiring tube amp but yeah, if it has a printed circuit board those would be the first choice. Good Call!
    Last edited by Bubbalou; 10-06-2024 at 02:56 PM.

  5. #5
    Forum Member Offshore Angler's Avatar
    Join Date
    Sep 2003
    Location
    New York Finger Lakes Area
    Posts
    8,530

    Re: Tube amp noise at start up

    Would turn out the lights and watch what the tubes do at power on.

    IIRC that amp has a standby, so does it do it in standby or just when you take it off standby?


    Chuck
    "No harmonic knowledge, no sense of time, a ghastly tone, unskilled vibrato, and so on. Chuck is one of the worst guitar players I know" -Gravity Jim

  6. #6
    Forum Member
    Join Date
    Aug 2008
    Location
    SW New Mexico, USA
    Posts
    1,674

    Re: Tube amp noise at start up

    I agree with Phantomman, too many times a poor solder connection has been the problem on the BJ, and Hot Rod amps. I don't use "lead free" solder for repairs!

  7. #7
    Forum Member phantomman's Avatar
    Join Date
    Aug 2007
    Location
    Ten miles from the Mexican Frontier, in Arizona
    Posts
    7,332

    Re: Tube amp noise at start up

    Quote Originally Posted by Bill Moore View Post
    I don't use "lead free" solder for repairs!
    Are you worried that young ghetto kids or fascists from the EPA would lick those solder joints?

    "When injustice becomes law then rebellion becomes duty."

  8. #8
    Forum Member
    Join Date
    Aug 2008
    Location
    SW New Mexico, USA
    Posts
    1,674

    Re: Tube amp noise at start up

    Lead free solder is "brittle", it takes more heat to melt, and 60/40 flows easier. I think a lot of the poor connection/cracked solder joints are due to lead free use.

  9. #9
    Forum Member Tele-Bob's Avatar
    Join Date
    Aug 2003
    Location
    Connecticut
    Posts
    6,740

    Re: Tube amp noise at start up

    I would simply move the tubes around in their sockets a little and make sure they're reset firmly in place. Probably all you need to do.
    If you're bored, you're not groovin'.

  10. #10
    Forum Member Offshore Angler's Avatar
    Join Date
    Sep 2003
    Location
    New York Finger Lakes Area
    Posts
    8,530

    Re: Tube amp noise at start up

    Quote Originally Posted by Tele-Bob View Post
    I would simply move the tubes around in their sockets a little and make sure they're reset firmly in place. Probably all you need to do.
    Agreed. "Never left the house and rarely played" is the key here. Tube amps don't usually fair too well being parked and not used. They need a jostling once in a while to keep them happy.

    Chuck
    "No harmonic knowledge, no sense of time, a ghastly tone, unskilled vibrato, and so on. Chuck is one of the worst guitar players I know" -Gravity Jim

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •