Results 1 to 8 of 8

Thread: cap job on a vibrolux

  1. #1
    Forum Member
    Join Date
    Mar 2003
    Location
    Pensacola, FL
    Posts
    30

    cap job on a vibrolux

    How much should I expect to pay for a cap job on a fender Vibrolux narrow panel. I don't want to send it to someone, and pay too much for a shoddy job. Another question is: Can I do this myself? I have basic knowlege of electronic components and know the dangers and risks involved. The schematic on the amp doesn't look too complex, and from looking at the guts of the amp I think I could handle it. But is there anything I need to know before proceeding. Part of me would rather let a professional do it, but the DIYer part of me wants to heat up the soldering iron and go to town. Any help would be greatly appreciated.

  2. #2
    Forum Member mrhappy's Avatar
    Join Date
    Nov 2002
    Posts
    40
    It pretty easy to do...The most important things are probably to make sure that they are discharged before you start playing around and.... pay CLOSE attention to the polarity of EACH cap...cause sometimes they try and trick you to see if you were paying attention.

  3. #3
    Forum Member Teleologist's Avatar
    Join Date
    Aug 2002
    Posts
    367
    The one to watch out for is the bias supply cap - it's connected positive to ground(the other end is the negative bias supply).

  4. #4
    Forum Member
    Join Date
    Mar 2003
    Location
    Pensacola, FL
    Posts
    30
    Anyone familiar with the vibrolux? I asked the local amp guy here in Baton Rouge and he said 100 bucks would do it. Is that reasonable?

  5. #5
    Forum Member
    Join Date
    Mar 2003
    Location
    Pensacola, FL
    Posts
    30
    Another question regarding bringing up the amp: I've read about people hooking up the amp to a variac, running a current through the amp and increasing voltage steadily. Is this necessary after installing new capacitors? I've only read a little on it and would definitely read more if I decide to take on the task of refurbing this amp.

  6. #6
    Forum Member
    Join Date
    Aug 2023
    Posts
    1

    Re: cap job on a vibrolux

    Quote Originally Posted by sigandstrat View Post
    How much should I expect to pay for a cap job on a fender Vibrolux
    I have the same question. It was never answered. How much did it cost you?

  7. #7
    Forum Member phantomman's Avatar
    Join Date
    Aug 2007
    Location
    Ten miles from the Mexican Frontier, in Arizona
    Posts
    7,321

    Re: cap job on a vibrolux

    $150 for a comprehensive cap job on a vintage Fender amp is not out of line. By 'comprehensive' I'm referring to the filter array and bias cap in the power supply plus the cathode-bypass caps on the main board.
    "When injustice becomes law then rebellion becomes duty."

  8. #8
    Forum Member Michael Smith's Avatar
    Join Date
    Dec 2021
    Location
    Southeast Texas
    Posts
    692

    Re: cap job on a vibrolux

    One variable that can affect the cost of a cap job is the brand of caps used. If you go to the cap set page on a site like Antique Electronics Supply, you will see a significant variation between the cost of the "premium" caps and the "basic" MOD caps. On the first 2 amps I recapped, I went with the premium F&T caps, but switched to MOD caps on the next 2 amps.

    About 2 hours labor seems about right for a professional amp tech to do a cap job, including checking and replacing any out of spec resistors, cleaning all pots and jack sockets, tightening all hardware. I replace the carbon comp resistors in the "doghouse" with metal film or oxide resistors. On the last amp I worked on, I also replaced the diode and resistor (along with the cap) in the bias supply, just because the parts are cheap and it's easy to do when replacing the cap.

    It takes me longer than 2 hours, because I am a hobbyist, and in no hurry. I bought a second inexpensive digital multimeter, which makes setting the bias quicker on a push-pull circuit.
    "When You're Riding Down the Highway at Night, And You're Feeling that Wild Turkey's Bite" ZZ Top

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •